MB7UAL Telemetry

This is the latest recevied telemetry packets stored in our database for station/object MB7UAL. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	CabT*
1753644355	13.88 Volt	100 Pcnt	169 c
1753643447	13.88 Volt	100 Pcnt	169 c
1753642547	13.88 Volt	100 Pcnt	170 c
1753641647	13.88 Volt	100 Pcnt	170 c
1753640747	13.88 Volt	100 Pcnt	170 c
1753639847	13.88 Volt	100 Pcnt	170 c
1753638947	13.88 Volt	100 Pcnt	171 c
1753638047	13.88 Volt	100 Pcnt	171 c
1753637147	13.88 Volt	100 Pcnt	171 c
1753636247	13.88 Volt	100 Pcnt	171 c
1753635347	13.88 Volt	100 Pcnt	172 c
1753634447	13.88 Volt	100 Pcnt	172 c
1753633547	13.88 Volt	100 Pcnt	172 c
1753632647	13.88 Volt	100 Pcnt	172 c
1753631747	13.88 Volt	100 Pcnt	171 c
1753630847	13.88 Volt	100 Pcnt	171 c
1753629047	13.88 Volt	100 Pcnt	173 c
1753628147	13.88 Volt	100 Pcnt	172 c
1753627247	13.88 Volt	100 Pcnt	172 c
1753626347	13.88 Volt	100 Pcnt	171 c
1753625447	13.88 Volt	100 Pcnt	171 c
1753624547	13.88 Volt	100 Pcnt	171 c
1753623647	13.88 Volt	100 Pcnt	171 c
1753622747	13.88 Volt	100 Pcnt	172 c
1753621847	13.88 Volt	100 Pcnt	172 c

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

CabT: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)