VA3LCI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VA3LCI. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Rx10m*
1765523771	14.22 Volt	50 Pcnt	3 Pkt
1765523471	14.22 Volt	54 Pcnt	1 Pkt
1765523171	14.22 Volt	50 Pcnt	0 Pkt
1765522871	14.22 Volt	46 Pcnt	0 Pkt
1765522571	14.22 Volt	46 Pcnt	0 Pkt
1765522271	14.22 Volt	46 Pcnt	0 Pkt
1765521971	14.22 Volt	46 Pcnt	1 Pkt
1765521671	14.22 Volt	46 Pcnt	1 Pkt
1765521372	14.22 Volt	46 Pcnt	1 Pkt
1765521071	14.22 Volt	50 Pcnt	1 Pkt
1765520794	14.22 Volt	50 Pcnt	0 Pkt
1765520472	14.22 Volt	55 Pcnt	3 Pkt
1765520172	14.22 Volt	44 Pcnt	3 Pkt
1765519872	14.22 Volt	44 Pcnt	1 Pkt
1765519572	14.22 Volt	50 Pcnt	0 Pkt
1765519272	14.22 Volt	57 Pcnt	0 Pkt
1765518972	14.22 Volt	40 Pcnt	0 Pkt
1765518672	14.22 Volt	33 Pcnt	0 Pkt
1765518372	14.22 Volt	26 Pcnt	1 Pkt
1765518072	14.22 Volt	25 Pcnt	1 Pkt
1765517772	14.22 Volt	29 Pcnt	0 Pkt
1765517472	14.22 Volt	29 Pcnt	0 Pkt
1765517172	14.22 Volt	29 Pcnt	0 Pkt
1765516872	14.22 Volt	31 Pcnt	2 Pkt
1765516572	14.22 Volt	35 Pcnt	3 Pkt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Rx10m: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)