DB0LOL-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0LOL-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vin*	Temp*	Eff1h*
1773061647	12.6 Volt	1280 C	100 Pcnt
1773061348	12.6 Volt	1280 C	100 Pcnt
1773061347	12.6 Volt	1280 C	100 Pcnt
1773061047	12.6 Volt	1280 C	100 Pcnt
1773060748	12.6 Volt	1280 C	100 Pcnt
1773060747	12.6 Volt	1280 C	100 Pcnt
1773060450	12.6 Volt	1280 C	100 Pcnt
1773060148	12.6 Volt	1280 C	100 Pcnt
1773060147	12.6 Volt	1280 C	100 Pcnt
1773059847	12.6 Volt	1280 C	100 Pcnt
1773059548	12.6 Volt	1280 C	100 Pcnt
1773059547	12.6 Volt	1280 C	100 Pcnt
1773059247	12.6 Volt	1280 C	100 Pcnt
1773058948	12.6 Volt	1280 C	100 Pcnt
1773058947	12.6 Volt	1280 C	100 Pcnt
1773058647	12.6 Volt	1280 C	100 Pcnt
1773058348	12.6 Volt	1280 C	100 Pcnt
1773058347	12.6 Volt	1280 C	100 Pcnt
1773058047	12.6 Volt	1280 C	100 Pcnt
1773057748	12.6 Volt	1280 C	100 Pcnt
1773057747	12.6 Volt	1280 C	100 Pcnt
1773057447	12.6 Volt	1280 C	100 Pcnt
1773057147	12.6 Volt	1280 C	100 Pcnt
1773056847	12.6 Volt	1280 C	100 Pcnt
1773056548	12.6 Volt	1280 C	100 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Temp: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)