This is the latest recevied telemetry packets stored in our database for station/object KC7CVI-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Battery*
Charging/AC*
GPS+Sat*
Current*
A5*
1755963926
86 Percent
2 Charge/On/Off
95 Sats/On/Off
0 mA
0 N/A
1755963610
86 Percent
2 Charge/On/Off
95 Sats/On/Off
0 mA
0 N/A
1755962350
89 Percent
2 Charge/On/Off
95 Sats/On/Off
0 mA
0 N/A
1755962230
89 Percent
2 Charge/On/Off
95 Sats/On/Off
0 mA
0 N/A
1755961750
91 Percent
2 Charge/On/Off
95 Sats/On/Off
0 mA
0 N/A
1755961570
91 Percent
2 Charge/On/Off
95 Sats/On/Off
0 mA
0 N/A
1755961272
92 Percent
2 Charge/On/Off
95 Sats/On/Off
0 mA
0 N/A
1755657494
80 Percent
2 Charge/On/Off
95 Sats/On/Off
0 mA
0 N/A
1755657074
81 Percent
2 Charge/On/Off
95 Sats/On/Off
0 mA
0 N/A
1755656894
82 Percent
2 Charge/On/Off
95 Sats/On/Off
0 mA
0 N/A
1755656654
82 Percent
2 Charge/On/Off
88 Sats/On/Off
0 mA
0 N/A
1755656594
82 Percent
2 Charge/On/Off
78 Sats/On/Off
0 mA
0 N/A
1755656474
83 Percent
2 Charge/On/Off
48 Sats/On/Off
0 mA
0 N/A
*Used Equation Coefficients:
Battery: 0, 1, 0
Charging/AC: 0, 1, 0
GPS+Sat: 0, 1, 0
Current: 0, 10, -1280
A5: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)