OE5XDO-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE5XDO-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	U-Netz*	U-Akku*	STBY*	BUSY*
1784672919	13.57 V	12.44 V	0 cnt	0 cnt
1784672619	13.57 V	12.44 V	0 cnt	0 cnt
1784672319	13.57 V	12.44 V	0 cnt	0 cnt
1784672020	13.57 V	12.44 V	0 cnt	0 cnt
1784671720	13.57 V	12.44 V	0 cnt	0 cnt
1784671421	13.57 V	12.45 V	0 cnt	0 cnt
1784671125	13.57 V	12.44 V	2 cnt	20 cnt
1784670822	13.57 V	12.44 V	2 cnt	20 cnt
1784670522	13.57 V	12.45 V	2 cnt	20 cnt
1784670222	13.57 V	12.45 V	2 cnt	20 cnt
1784669924	13.57 V	12.45 V	2 cnt	20 cnt
1784669324	13.57 V	12.45 V	2 cnt	20 cnt
1784668424	13.57 V	12.45 V	2 cnt	20 cnt
1784668125	13.57 V	12.44 V	2 cnt	20 cnt
1784667825	13.57 V	12.45 V	2 cnt	20 cnt
1784667526	13.57 V	12.45 V	2 cnt	20 cnt
1784667230	13.59 V	12.45 V	2 cnt	20 cnt
1784666927	13.57 V	12.45 V	2 cnt	20 cnt
1784666627	13.57 V	12.45 V	2 cnt	20 cnt
1784666327	13.57 V	12.45 V	2 cnt	20 cnt
1784666029	13.57 V	12.44 V	2 cnt	20 cnt
1784665728	13.57 V	12.44 V	2 cnt	20 cnt
1784665428	13.57 V	12.45 V	2 cnt	20 cnt
1784665129	13.57 V	12.44 V	2 cnt	20 cnt
1784664829	13.57 V	12.45 V	2 cnt	20 cnt

*Used Equation Coefficients:

U-Netz: 0, 0.01, 0

U-Akku: 0, 0.01, 0

STBY: 0, 1, 0

BUSY: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)