SR2ATJ-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR2ATJ-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1780597241	124 Count	813 Count	4.01 VDC
1780595441	120 Count	786 Count	4.01 VDC
1780593640	116 Count	759 Count	4.02 VDC
1780591839	112 Count	723 Count	4.02 VDC
1780590038	107 Count	693 Count	4.02 VDC
1780588237	103 Count	664 Count	4.02 VDC
1780586437	97 Count	633 Count	4.02 VDC
1780584636	93 Count	600 Count	4.02 VDC
1780582835	88 Count	559 Count	4.03 VDC
1780581035	84 Count	534 Count	4.03 VDC
1780579234	79 Count	505 Count	4.03 VDC
1780575648	66 Count	431 Count	4.03 VDC
1780573848	62 Count	402 Count	4.02 VDC
1780572047	56 Count	372 Count	4.03 VDC
1780570246	52 Count	344 Count	4.03 VDC
1780568445	47 Count	322 Count	4.03 VDC
1780566644	43 Count	296 Count	4.02 VDC
1780564843	38 Count	268 Count	4.02 VDC
1780563043	34 Count	237 Count	4.02 VDC
1780561242	29 Count	206 Count	4.02 VDC
1780559441	25 Count	176 Count	4.02 VDC
1780557641	18 Count	147 Count	4.02 VDC
1780554039	7 Count	68 Count	4.01 VDC
1780552239	3 Count	34 Count	4.01 VDC
1780550438	167 Count	1008 Count	4 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)