BV2CW-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV2CW-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1787583153	49.9 C	0 p	0 p	167 p
1787581953	51.1 C	0 p	0 p	167 p
1787580753	49.9 C	0 p	43 p	167 p
1787579553	50.8 C	0 p	87 p	167 p
1787578353	50.5 C	43 p	87 p	167 p
1787577153	49.2 C	44 p	45 p	124 p
1787575954	49.5 C	0 p	1 p	80 p
1787574753	49.7 C	1 p	1 p	80 p
1787573553	49.9 C	0 p	0 p	79 p
1787572353	49.2 C	0 p	0 p	79 p
1787571153	50.3 C	0 p	0 p	79 p
1787569953	50.6 C	0 p	4 p	79 p
1787568753	49.5 C	0 p	4 p	79 p
1787567553	49.5 C	4 p	4 p	79 p
1787566422	49.5 C	0 p	0 p	75 p
1787565153	50.4 C	0 p	0 p	75 p
1787563953	49.5 C	0 p	7 p	75 p
1787562753	49.2 C	0 p	7 p	75 p
1787561554	49.9 C	7 p	27 p	75 p
1787560353	50.2 C	0 p	45 p	68 p
1787559153	49.4 C	20 p	45 p	68 p
1787557953	49.9 C	25 p	25 p	48 p
1787556753	50 C	0 p	0 p	23 p
1787555553	48.7 C	0 p	10 p	23 p
1787554353	50.6 C	0 p	10 p	23 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)