YO9RIJ-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO9RIJ-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	T ext.*	Value2*	Value3*	Value4*	Value5*
1762386097	15.6 °C	0	0	0	0
1762385496	15.6 °C	0	0	0	0
1762384897	15.5 °C	0	0	0	0
1762384297	15.6 °C	0	0	0	0
1762383696	15.6 °C	0	0	0	0
1762383097	14.4 °C	0	0	0	0
1762382522	15.6 °C	0	0	0	0
1762381896	15.7 °C	0	0	0	0
1762381297	15.6 °C	0	0	0	0
1762380697	15.8 °C	0	0	0	0
1762380096	15.8 °C	0	0	0	0
1762379497	15.8 °C	0	0	0	0
1762378897	15.9 °C	0	0	0	0
1762377698	15.9 °C	0	0	0	0
1762377097	15.9 °C	0	0	0	0
1762376496	15.9 °C	0	0	0	0
1762375897	15.9 °C	0	0	0	0
1762375297	15.9 °C	0	0	0	0
1762374696	15.9 °C	0	0	0	0
1762374097	15.9 °C	0	0	0	0
1762373497	15.9 °C	0	0	0	0
1762372297	16 °C	0	0	0	0
1762371697	16.1 °C	0	0	0	0
1762371097	16 °C	0	0	0	0
1762370498	15.9 °C	0	0	0	0

*Used Equation Coefficients:

T ext.: 0, 1, -100

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)