M0UPS-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object M0UPS-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BattSOC*	Volt*	Curr*	Rad*
1782360003	92 %	12.6 V	-0.5 A	12 uR/h
1782359703	92 %	12.6 V	-0.5 A	9 uR/h
1782359403	92 %	12.6 V	-0.5 A	14 uR/h
1782359103	92 %	12.6 V	-0.5 A	5 uR/h
1782358803	92 %	12.6 V	-0.5 A	6 uR/h
1782358503	92 %	12.6 V	-0.5 A	7 uR/h
1782358203	92 %	12.6 V	-0.5 A	7 uR/h
1782357904	92 %	12.6 V	-0.5 A	4 uR/h
1782357603	92 %	12.6 V	-0.5 A	14 uR/h
1782357303	92 %	12.6 V	-0.5 A	10 uR/h
1782357002	92 %	12.6 V	-0.5 A	8 uR/h
1782356702	92 %	12.6 V	-0.5 A	13 uR/h
1782356404	92 %	12.6 V	-0.5 A	10 uR/h
1782356102	92 %	12.6 V	-0.5 A	12 uR/h
1782355803	92 %	12.6 V	-0.5 A	7 uR/h
1782355503	92 %	12.6 V	-0.5 A	7 uR/h
1782355203	92 %	12.6 V	-0.5 A	13 uR/h
1782354903	92 %	12.6 V	-0.5 A	11 uR/h
1782354603	92 %	12.6 V	-0.5 A	10 uR/h
1782354302	92 %	12.6 V	-0.5 A	8 uR/h
1782354003	92 %	12.6 V	-0.5 A	9 uR/h
1782353703	92 %	12.6 V	-0.5 A	10 uR/h
1782353403	92 %	12.6 V	-0.5 A	9 uR/h
1782353103	92 %	12.6 V	-0.5 A	11 uR/h
1782352804	92 %	12.6 V	-0.5 A	10 uR/h

*Used Equation Coefficients:

BattSOC: 0, 1, 0

Volt: 0, 0.1, 0

Curr: 0, 0.5, -50

Rad: 0, 1, 0

Unused: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)