TA1FL-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA1FL-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1772860028	13.65 Volt	930 Pkt	73 Pcnt
1772859971	13.65 Volt	950 Pkt	73 Pcnt
1772859671	13.65 Volt	940 Pkt	73 Pcnt
1772859671	13.65 Volt	940 Pkt	73 Pcnt
1772859370	13.65 Volt	950 Pkt	73 Pcnt
1772859072	13.65 Volt	930 Pkt	73 Pcnt
1772859070	13.65 Volt	930 Pkt	73 Pcnt
1772858770	13.65 Volt	920 Pkt	73 Pcnt
1772858607	13.65 Volt	930 Pkt	73 Pcnt
1772858474	13.65 Volt	930 Pkt	74 Pcnt
1772858469	13.65 Volt	930 Pkt	74 Pcnt
1772858169	13.65 Volt	930 Pkt	73 Pcnt
1772858070	13.65 Volt	920 Pkt	72 Pcnt
1772857870	13.65 Volt	930 Pkt	73 Pcnt
1772857869	13.65 Volt	930 Pkt	73 Pcnt
1772857576	13.65 Volt	920 Pkt	73 Pcnt
1772857569	13.65 Volt	930 Pkt	73 Pcnt
1772857269	13.65 Volt	920 Pkt	72 Pcnt
1772857268	13.65 Volt	920 Pkt	72 Pcnt
1772857000	13.65 Volt	920 Pkt	74 Pcnt
1772856968	13.65 Volt	910 Pkt	73 Pcnt
1772856668	13.65 Volt	920 Pkt	73 Pcnt
1772856668	13.65 Volt	920 Pkt	73 Pcnt
1772856367	13.65 Volt	920 Pkt	74 Pcnt
1772856069	13.65 Volt	920 Pkt	74 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)