This is the latest recevied telemetry packets stored in our database for station/object KK7MNC-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Battery*
Charging/AC*
GPS+Sat*
Current*
A5*
1761525116
94 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1761520556
94 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1761518936
94 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1761270070
97 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1761269110
97 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1761267250
97 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1761266350
97 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1761264495
97 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1761263590
97 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1761183648
97 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1761182748
97 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1761181848
97 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1761180888
97 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
*Used Equation Coefficients:
Battery: 0, 1, 0
Charging/AC: 0, 1, 0
GPS+Sat: 0, 1, 0
Current: 0, 10, -1280
A5: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)