VR2WUK Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VR2WUK. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPU*	Temp*	FreeM*
1772684237	0.24 Load	47.77 °C	622 Mb
1772683928	0.28 Load	48.85 °C	624 Mb
1772683628	0.25 Load	48.31 °C	624 Mb
1772683328	0.25 Load	48.31 °C	623 Mb
1772683018	0.24 Load	47.77 °C	623 Mb
1772682719	0.22 Load	48.31 °C	626 Mb
1772682409	0.24 Load	48.31 °C	623 Mb
1772682099	0.25 Load	48.31 °C	623 Mb
1772681799	0.28 Load	48.31 °C	623 Mb
1772681489	0.27 Load	48.31 °C	623 Mb
1772681179	0.27 Load	48.31 °C	624 Mb
1772680879	0.23 Load	47.77 °C	624 Mb
1772680569	0.27 Load	47.77 °C	624 Mb
1772680259	0.24 Load	48.31 °C	625 Mb
1772679961	0.23 Load	47.77 °C	625 Mb
1772679659	0.29 Load	47.77 °C	624 Mb
1772679349	0.27 Load	47.77 °C	624 Mb
1772679049	0.32 Load	48.31 °C	625 Mb
1772678739	0.22 Load	48.31 °C	625 Mb
1772678429	0.21 Load	47.77 °C	625 Mb
1772678129	0.23 Load	48.31 °C	625 Mb
1772677819	0.24 Load	47.77 °C	625 Mb
1772677509	0.25 Load	47.77 °C	626 Mb
1772677209	0.22 Load	47.77 °C	625 Mb
1772676899	0.23 Load	47.77 °C	625 Mb

*Used Equation Coefficients:

CPU: 0, 0.001, 0

Temp: 0, 0.001, 0

FreeM: 0, 1, 0

RxP: 0, 1, 0

TxP: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)