9A4QV-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9A4QV-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1788564314	12.09 Volt	1950 Pkt	68 Pcnt
1788563413	12.09 Volt	2050 Pkt	70 Pcnt
1788562512	12.09 Volt	2130 Pkt	70 Pcnt
1788561611	12.09 Volt	2200 Pkt	71 Pcnt
1788560711	12.09 Volt	2210 Pkt	73 Pcnt
1788559810	12.09 Volt	2190 Pkt	73 Pcnt
1788558909	12.09 Volt	2230 Pkt	74 Pcnt
1788558008	12.09 Volt	2240 Pkt	74 Pcnt
1788557107	12.09 Volt	2250 Pkt	72 Pcnt
1788556206	12.09 Volt	2290 Pkt	72 Pcnt
1788555305	12.09 Volt	2250 Pkt	71 Pcnt
1788554404	12.09 Volt	2310 Pkt	72 Pcnt
1788553504	12.09 Volt	2340 Pkt	73 Pcnt
1788552603	12.09 Volt	2380 Pkt	73 Pcnt
1788551702	12.09 Volt	2410 Pkt	74 Pcnt
1788550801	12.09 Volt	2380 Pkt	73 Pcnt
1788549900	12.09 Volt	2300 Pkt	72 Pcnt
1788548999	12.09 Volt	2210 Pkt	70 Pcnt
1788548098	12.09 Volt	2180 Pkt	69 Pcnt
1788547197	12.09 Volt	2200 Pkt	69 Pcnt
1788546297	12.09 Volt	2220 Pkt	70 Pcnt
1788545396	12.09 Volt	2260 Pkt	71 Pcnt
1788544495	12.09 Volt	2270 Pkt	72 Pcnt
1788543594	12.09 Volt	2220 Pkt	72 Pcnt
1788542693	12.09 Volt	2190 Pkt	71 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)