OE9DGV-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE9DGV-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1757606822	17.6 deg C	71.7 %	1015.3 hPa
1757605021	17.6 deg C	71.8 %	1015.2 hPa
1757604125	17.5 deg C	73.1 %	1015.2 hPa
1757603223	17.5 deg C	72.9 %	1016.2 hPa
1757602325	17.6 deg C	73.8 %	1016.1 hPa
1757600530	17.9 deg C	70.5 %	1015.9 hPa
1757599625	18 deg C	71.3 %	1014.7 hPa
1757598720	18.3 deg C	67.7 %	1014.6 hPa
1757596920	18.6 deg C	68 %	1014.4 hPa
1757596020	18.7 deg C	67.9 %	1014.2 hPa
1757595124	18.7 deg C	70.6 %	1014.2 hPa
1757594220	18.8 deg C	74.4 %	1014.2 hPa
1757593324	18.5 deg C	77 %	1014.2 hPa
1757592425	18.4 deg C	75.1 %	1014.3 hPa
1757591523	18.4 deg C	76 %	1014.2 hPa
1757590628	18.6 deg C	76.3 %	1014 hPa
1757589730	19 deg C	76.3 %	1013.8 hPa
1757588835	18.8 deg C	76.3 %	1013.7 hPa
1757587940	19 deg C	77 %	1013.6 hPa
1757582549	17.8 deg C	78.7 %	1013.5 hPa
1757581654	17.2 deg C	83.7 %	1013.6 hPa
1757580755	16.9 deg C	85.3 %	1013.7 hPa
1757579858	16.8 deg C	85.3 %	1013.6 hPa
1757578954	16.5 deg C	86.3 %	1013.6 hPa
1757578055	16.3 deg C	86.6 %	1013.6 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)