DG0HAB-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG0HAB-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Temp*	Humi*	Baro*
1780590818	23.5 deg C	51.8 %	1003.3 hPa
1780589918	23.5 deg C	51.8 %	1003.4 hPa
1780589018	23.5 deg C	51.7 %	1003.2 hPa
1780588687	23.5 deg C	51.7 %	1003.1 hPa
1780587787	23.5 deg C	51.8 %	1002.8 hPa
1780586888	23.5 deg C	51.5 %	1002.1 hPa
1780585987	23.5 deg C	51.3 %	1001.8 hPa
1780585087	23.5 deg C	51.2 %	1001.9 hPa
1780584186	23.5 deg C	51.2 %	1003.8 hPa
1780583286	23.5 deg C	51.1 %	1004.2 hPa
1780582386	23.6 deg C	51.1 %	1003.6 hPa
1780581486	23.6 deg C	51.1 %	1004.3 hPa
1780580586	23.6 deg C	51.2 %	1003.7 hPa
1780579686	23.6 deg C	51.2 %	1003.5 hPa
1780578786	23.6 deg C	51.2 %	1003.5 hPa
1780577886	23.5 deg C	51.2 %	1004.8 hPa
1780576986	23.5 deg C	51.1 %	1004.5 hPa
1780576657	23.5 deg C	51 %	1004.6 hPa
1780575757	23.5 deg C	51 %	1005.1 hPa
1780574857	23.5 deg C	51 %	1005 hPa
1780573956	23.4 deg C	50.9 %	1005.4 hPa
1780573056	23.4 deg C	51 %	1004 hPa
1780572156	23.4 deg C	51 %	1004.8 hPa
1780571256	23.4 deg C	51.1 %	1005.1 hPa
1780570356	23.3 deg C	51.1 %	1004.9 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)