SR2LFD-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR2LFD-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	V_Bat*	V_Ext*
1782156658	4.32 VDC	0.18 VDC
1782154858	4.28 VDC	0.18 VDC
1782153058	4.27 VDC	0.18 VDC
1782151258	4.26 VDC	0.2 VDC
1782143782	4.27 VDC	0.18 VDC
1782141982	4.29 VDC	0.2 VDC
1782069813	4.29 VDC	0.18 VDC
1782068013	4.22 VDC	0.18 VDC
1782066212	4.21 VDC	0.14 VDC
1782065749	4.24 VDC	0.16 VDC
1782063949	4.25 VDC	0.18 VDC
1782062149	4.31 VDC	0.18 VDC
1782060349	4.29 VDC	0.18 VDC
1782058549	4.3 VDC	0.14 VDC
1782057788	4.22 VDC	0.18 VDC
1782055988	4.24 VDC	0.18 VDC
1782054188	4.3 VDC	0.18 VDC
1782052388	4.24 VDC	0.18 VDC
1782050588	4.28 VDC	0.16 VDC
1782050528	4.27 VDC	0.14 VDC
1782050455	4.27 VDC	0.14 VDC
1782050375	4.25 VDC	0.14 VDC
1782050295	4.23 VDC	0.14 VDC
1782050239	4.29 VDC	0.14 VDC
1782050175	4.27 VDC	0.16 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)