W4IOJ-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W4IOJ-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1776655195	12.3 Volt	10 Pkt	26 Pcnt
1776655192	12.3 Volt	10 Pkt	23 Pcnt
1776655189	12.3 Volt	20 Pkt	31 Pcnt
1776655160	12.3 Volt	10 Pkt	23 Pcnt
1776655159	12.3 Volt	10 Pkt	28 Pcnt
1776655158	12.3 Volt	10 Pkt	26 Pcnt
1776655157	12.3 Volt	20 Pkt	29 Pcnt
1776655156	12.3 Volt	20 Pkt	31 Pcnt
1776655155	12.3 Volt	20 Pkt	32 Pcnt
1776655151	12.3 Volt	30 Pkt	45 Pcnt
1776636962	12.3 Volt	20 Pkt	43 Pcnt
1776636962	12.3 Volt	20 Pkt	44 Pcnt
1776636959	12.3 Volt	20 Pkt	48 Pcnt
1776636958	12.3 Volt	20 Pkt	43 Pcnt
1776636957	12.3 Volt	20 Pkt	42 Pcnt
1776633947	12.3 Volt	10 Pkt	33 Pcnt
1776633946	12.3 Volt	10 Pkt	29 Pcnt
1776633945	12.3 Volt	20 Pkt	40 Pcnt
1776633943	12.3 Volt	20 Pkt	47 Pcnt
1776631547	12.23 Volt	20 Pkt	49 Pcnt
1776630956	12.3 Volt	20 Pkt	46 Pcnt
1776630329	12.3 Volt	20 Pkt	57 Pcnt
1776629968	12.3 Volt	20 Pkt	60 Pcnt
1776629578	12.3 Volt	20 Pkt	52 Pcnt
1776629576	12.3 Volt	20 Pkt	58 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)