DJ9FBA-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DJ9FBA-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1776535842	24.7 C	31.96 %	1023.25 hPa
1776526812	29.1 C	24.22 %	1021.25 hPa
1776517782	29.3 C	28.94 %	1023 hPa
1776508752	25.9 C	36.49 %	1020.38 hPa
1776500558	22.9 C	43.83 %	1025.88 hPa
1776492232	21.2 C	45.16 %	1025 hPa
1776483202	20.8 C	45.28 %	1022.5 hPa
1776474172	21.5 C	44.44 %	1023.5 hPa
1776465142	22.3 C	43.09 %	1026.13 hPa
1776456112	23.5 C	40.41 %	1022.38 hPa
1776447082	26.2 C	29.34 %	1018.88 hPa
1776438035	33.3 C	17.98 %	993.88 hPa
1776397106	19.7 C	45.19 %	1025.88 hPa
1776388076	20.3 C	45.35 %	1025.38 hPa
1776379046	21 C	45.64 %	1024.63 hPa
1776370016	22.4 C	43.95 %	1025.5 hPa
1776360986	24.7 C	36 %	1021.88 hPa
1776351956	31.5 C	23.65 %	1024.63 hPa
1776342894	23.6 C	39.99 %	996.38 hPa
1776321434	19.1 C	47.21 %	996.5 hPa
1776297439	20.3 C	43.9 %	1023 hPa
1776288409	21.6 C	40.57 %	1022.13 hPa
1776280004	22.8 C	37.71 %	1021.38 hPa
1776270974	29 C	24.78 %	1020.38 hPa
1776261927	26.1 C	29.24 %	994.5 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)