LAPEER Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LAPEER. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1776703851	12.6 Volt	100 Pkt	50 Pkt	97 Pcnt
1776703551	12.75 Volt	100 Pkt	50 Pkt	98 Pcnt
1776703251	12.68 Volt	100 Pkt	50 Pkt	98 Pcnt
1776702951	12.75 Volt	100 Pkt	50 Pkt	99 Pcnt
1776702651	12.75 Volt	100 Pkt	50 Pkt	99 Pcnt
1776702351	12.75 Volt	100 Pkt	50 Pkt	100 Pcnt
1776702051	12.75 Volt	100 Pkt	50 Pkt	100 Pcnt
1776701751	12.75 Volt	100 Pkt	50 Pkt	100 Pcnt
1776701451	12.9 Volt	100 Pkt	50 Pkt	100 Pcnt
1776701151	12.9 Volt	110 Pkt	50 Pkt	100 Pcnt
1776700851	12.83 Volt	110 Pkt	50 Pkt	100 Pcnt
1776700551	12.83 Volt	110 Pkt	50 Pkt	99 Pcnt
1776700251	12.75 Volt	120 Pkt	50 Pkt	98 Pcnt
1776699951	12.83 Volt	120 Pkt	50 Pkt	97 Pcnt
1776699651	12.83 Volt	120 Pkt	50 Pkt	97 Pcnt
1776699351	12.83 Volt	120 Pkt	40 Pkt	97 Pcnt
1776699051	12.68 Volt	120 Pkt	50 Pkt	97 Pcnt
1776698751	12.75 Volt	120 Pkt	50 Pkt	97 Pcnt
1776698451	12.83 Volt	110 Pkt	50 Pkt	97 Pcnt
1776698151	12.68 Volt	110 Pkt	50 Pkt	97 Pcnt
1776697851	12.75 Volt	110 Pkt	40 Pkt	97 Pcnt
1776697551	12.75 Volt	110 Pkt	50 Pkt	95 Pcnt
1776697251	12.75 Volt	100 Pkt	40 Pkt	95 Pcnt
1776696951	12.83 Volt	100 Pkt	40 Pkt	95 Pcnt
1776696651	12.75 Volt	100 Pkt	40 Pkt	96 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)