9A3PRO-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9A3PRO-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1757596182	12.01 Volt	660 Pkt	62 Pcnt
1757595281	12.01 Volt	710 Pkt	65 Pcnt
1757594383	11.93 Volt	740 Pkt	65 Pcnt
1757594380	11.93 Volt	740 Pkt	65 Pcnt
1757593480	11.93 Volt	760 Pkt	66 Pcnt
1757592579	11.93 Volt	770 Pkt	67 Pcnt
1757591678	11.93 Volt	770 Pkt	66 Pcnt
1757590780	11.93 Volt	750 Pkt	66 Pcnt
1757590777	11.93 Volt	750 Pkt	66 Pcnt
1757589876	11.93 Volt	750 Pkt	65 Pcnt
1757588975	11.93 Volt	790 Pkt	66 Pcnt
1757588074	11.93 Volt	800 Pkt	68 Pcnt
1757587174	11.93 Volt	810 Pkt	69 Pcnt
1757587173	11.93 Volt	810 Pkt	69 Pcnt
1757586273	11.93 Volt	800 Pkt	69 Pcnt
1757585372	11.93 Volt	750 Pkt	68 Pcnt
1757584471	11.93 Volt	770 Pkt	67 Pcnt
1757583573	11.93 Volt	770 Pkt	67 Pcnt
1757583570	11.93 Volt	770 Pkt	67 Pcnt
1757582669	11.93 Volt	790 Pkt	66 Pcnt
1757581768	11.93 Volt	790 Pkt	67 Pcnt
1757580867	11.93 Volt	780 Pkt	66 Pcnt
1757579967	11.93 Volt	800 Pkt	66 Pcnt
1757579966	11.93 Volt	800 Pkt	66 Pcnt
1757579065	11.93 Volt	840 Pkt	68 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)