DL0PBS-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL0PBS-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	U1*	Temp*
1761546232	12.38 Volt	13.9 Volt	17.5 C
1761545932	12.38 Volt	13.9 Volt	17.5 C
1761545632	12.38 Volt	13.9 Volt	17.5 C
1761545332	12.38 Volt	13.9 Volt	17.5 C
1761545031	12.38 Volt	13.9 Volt	17.5 C
1761544731	12.38 Volt	13.9 Volt	17.5 C
1761544431	12.38 Volt	13.9 Volt	17.5 C
1761544130	12.38 Volt	13.9 Volt	17.5 C
1761543830	12.38 Volt	13.9 Volt	17.5 C
1761543530	12.38 Volt	13.9 Volt	17.5 C
1761543231	12.38 Volt	13.9 Volt	17.5 C
1761542929	12.38 Volt	13.9 Volt	17.5 C
1761542629	12.38 Volt	13.9 Volt	17.5 C
1761542329	12.38 Volt	13.9 Volt	17.5 C
1761542028	12.38 Volt	13.9 Volt	17.5 C
1761541728	12.38 Volt	13.9 Volt	17.5 C
1761541429	12.38 Volt	13.9 Volt	17.5 C
1761541127	12.38 Volt	13.9 Volt	17.5 C
1761540827	12.38 Volt	13.9 Volt	17.5 C
1761540528	12.38 Volt	13.9 Volt	17.5 C
1761540227	12.38 Volt	13.9 Volt	17.5 C
1761539926	12.38 Volt	13.9 Volt	17.5 C
1761539626	12.38 Volt	13.9 Volt	17.5 C
1761539326	12.38 Volt	13.9 Volt	17.5 C
1761539025	12.38 Volt	13.9 Volt	17.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

U1: 0, 0.1, 0

U2: 0, 0.1, 0

I1: 0, 19.5, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)