YO2CIP Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO2CIP. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPM*	CH2*	CH3*	CH4*	CH5*
1780618988	42 CPM	0 0	0 0	0 0	0 0
1780618923	46 CPM	0 0	0 0	0 0	0 0
1780618860	48 CPM	0 0	0 0	0 0	0 0
1780618800	60 CPM	0 0	0 0	0 0	0 0
1780618738	50 CPM	0 0	0 0	0 0	0 0
1780618677	54 CPM	0 0	0 0	0 0	0 0
1780618615	36 CPM	0 0	0 0	0 0	0 0
1780618552	50 CPM	0 0	0 0	0 0	0 0
1780618491	34 CPM	0 0	0 0	0 0	0 0
1780618430	46 CPM	0 0	0 0	0 0	0 0
1780618369	50 CPM	0 0	0 0	0 0	0 0
1780618307	30 CPM	0 0	0 0	0 0	0 0
1780618247	43 CPM	0 0	0 0	0 0	0 0
1780618184	50 CPM	0 0	0 0	0 0	0 0
1780618122	42 CPM	0 0	0 0	0 0	0 0
1780618061	44 CPM	0 0	0 0	0 0	0 0
1780618000	64 CPM	0 0	0 0	0 0	0 0
1780617938	54 CPM	0 0	0 0	0 0	0 0
1780617877	42 CPM	0 0	0 0	0 0	0 0
1780617810	50 CPM	0 0	0 0	0 0	0 0
1780617748	48 CPM	0 0	0 0	0 0	0 0
1780617686	50 CPM	0 0	0 0	0 0	0 0
1780617621	39 CPM	0 0	0 0	0 0	0 0
1780617557	41 CPM	0 0	0 0	0 0	0 0
1780617496	46 CPM	0 0	0 0	0 0	0 0

*Used Equation Coefficients:

CPM: 0, 1, 0

CH2: 0, 1, 0

CH3: 0, 1, 0

CH4: 0, 1, 0

CH5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)