SP8QEO-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP8QEO-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1784705625	12.98 Volt	40 Pkt	98 Pcnt
1784705624	12.98 Volt	40 Pkt	98 Pcnt
1784705324	14.18 Volt	50 Pkt	100 Pcnt
1784705025	13.13 Volt	40 Pkt	100 Pcnt
1784705024	13.13 Volt	40 Pkt	100 Pcnt
1784704724	13.35 Volt	40 Pkt	100 Pcnt
1784704425	13.2 Volt	40 Pkt	100 Pcnt
1784704424	13.2 Volt	40 Pkt	100 Pcnt
1784704124	14.18 Volt	50 Pkt	100 Pcnt
1784703825	13.13 Volt	40 Pkt	100 Pcnt
1784703824	13.13 Volt	40 Pkt	100 Pcnt
1784703524	13.35 Volt	40 Pkt	100 Pcnt
1784703225	13.2 Volt	40 Pkt	97 Pcnt
1784703224	13.2 Volt	40 Pkt	97 Pcnt
1784702924	13.28 Volt	40 Pkt	98 Pcnt
1784702625	13.43 Volt	50 Pkt	96 Pcnt
1784702624	13.43 Volt	50 Pkt	96 Pcnt
1784702324	13.2 Volt	50 Pkt	96 Pcnt
1784702025	13.73 Volt	40 Pkt	94 Pcnt
1784702024	13.73 Volt	40 Pkt	94 Pcnt
1784701742	12.98 Volt	40 Pkt	94 Pcnt
1784701425	14.25 Volt	40 Pkt	94 Pcnt
1784701424	14.25 Volt	40 Pkt	94 Pcnt
1784701124	13.35 Volt	40 Pkt	94 Pcnt
1784700825	13.13 Volt	50 Pkt	91 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)