OZ9DIJ-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OZ9DIJ-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1757525175	13.8 Volt	210 Pkt	70 Pkt	79 Pcnt
1757523073	13.8 Volt	180 Pkt	70 Pkt	71 Pcnt
1757516767	13.8 Volt	70 Pkt	50 Pkt	48 Pcnt
1757514665	13.8 Volt	100 Pkt	80 Pkt	57 Pcnt
1757512563	13.8 Volt	130 Pkt	100 Pkt	63 Pcnt
1757510461	13.8 Volt	120 Pkt	70 Pkt	63 Pcnt
1757508360	13.8 Volt	200 Pkt	120 Pkt	71 Pcnt
1757506257	13.8 Volt	210 Pkt	130 Pkt	80 Pcnt
1757504155	13.8 Volt	170 Pkt	130 Pkt	73 Pcnt
1757502053	13.8 Volt	180 Pkt	140 Pkt	61 Pcnt
1757499951	13.8 Volt	120 Pkt	90 Pkt	54 Pcnt
1757497849	13.8 Volt	110 Pkt	70 Pkt	52 Pcnt
1757495747	13.8 Volt	120 Pkt	70 Pkt	66 Pcnt
1757493645	13.8 Volt	170 Pkt	80 Pkt	73 Pcnt
1757491543	13.8 Volt	120 Pkt	70 Pkt	60 Pcnt
1757489441	13.8 Volt	120 Pkt	80 Pkt	52 Pcnt
1757485237	13.8 Volt	110 Pkt	60 Pkt	50 Pcnt
1757483135	13.8 Volt	220 Pkt	100 Pkt	64 Pcnt
1757481033	13.8 Volt	280 Pkt	120 Pkt	65 Pcnt
1757478931	13.8 Volt	280 Pkt	130 Pkt	63 Pcnt
1757476830	13.8 Volt	180 Pkt	90 Pkt	62 Pcnt
1757474727	13.8 Volt	160 Pkt	60 Pkt	53 Pcnt
1757472626	13.8 Volt	270 Pkt	120 Pkt	60 Pcnt
1757470524	13.8 Volt	390 Pkt	160 Pkt	65 Pcnt
1757468419	13.8 Volt	360 Pkt	140 Pkt	64 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)