YU4PTT-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YU4PTT-8. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1765586250	12.6 Volt	1080 Pkt	65 %
1765585676	12.6 Volt	1100 Pkt	66 %
1765585050	12.6 Volt	1120 Pkt	67 %
1765584450	12.6 Volt	1120 Pkt	67 %
1765583850	12.6 Volt	1110 Pkt	65 %
1765583250	12.6 Volt	1120 Pkt	65 %
1765582650	12.53 Volt	1070 Pkt	63 %
1765582050	12.53 Volt	1060 Pkt	62 %
1765581458	12.6 Volt	1070 Pkt	61 %
1765580850	12.6 Volt	1070 Pkt	62 %
1765580250	12.53 Volt	1120 Pkt	64 %
1765579650	12.6 Volt	1140 Pkt	65 %
1765579050	12.6 Volt	1190 Pkt	67 %
1765578451	12.53 Volt	1240 Pkt	69 %
1765577851	12.6 Volt	1210 Pkt	69 %
1765577251	12.6 Volt	1180 Pkt	70 %
1765576668	12.53 Volt	1130 Pkt	69 %
1765576051	12.6 Volt	1090 Pkt	69 %
1765575451	12.6 Volt	1030 Pkt	68 %
1765574851	12.6 Volt	970 Pkt	68 %
1765574251	12.53 Volt	970 Pkt	68 %
1765573651	12.6 Volt	930 Pkt	66 %
1765573051	12.6 Volt	900 Pkt	65 %
1765572451	12.6 Volt	860 Pkt	64 %
1765571851	12.53 Volt	810 Pkt	62 %

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Dg/Rx: 0, 0.001, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)