CT7BAF-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object CT7BAF-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	V_Bat*	V_Ext*
1776641103	589 Count	3.99 VDC	0.14 VDC
1776639300	588 Count	3.98 VDC	0.14 VDC
1776635729	586 Count	4.01 VDC	0.14 VDC
1776633926	585 Count	4.01 VDC	0.14 VDC
1776632123	584 Count	4 VDC	0.14 VDC
1776630320	583 Count	4.01 VDC	0.14 VDC
1776628517	582 Count	4.03 VDC	0.14 VDC
1776626714	581 Count	3.99 VDC	0.14 VDC
1776624910	580 Count	4.02 VDC	0.14 VDC
1776623107	579 Count	4.02 VDC	0.14 VDC
1776621304	578 Count	4.04 VDC	0.14 VDC
1776619501	577 Count	4.02 VDC	0.14 VDC
1776617698	576 Count	4 VDC	0.14 VDC
1776615895	575 Count	4 VDC	0.14 VDC
1776614127	574 Count	4 VDC	0.14 VDC
1776612324	573 Count	3.99 VDC	0.14 VDC
1776610521	572 Count	4.03 VDC	0.14 VDC
1776608718	571 Count	3.99 VDC	0.14 VDC
1776606915	570 Count	4.04 VDC	0.14 VDC
1776605112	569 Count	4.02 VDC	0.14 VDC
1776603309	568 Count	4 VDC	0.14 VDC
1776601506	567 Count	3.99 VDC	0.14 VDC
1776599704	566 Count	3.97 VDC	0.14 VDC
1776597901	565 Count	4 VDC	0.14 VDC
1776596098	564 Count	3.98 VDC	0.14 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)