OH2EKK-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OH2EKK-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	WM*	YK*	AK*	OUT MIINUS*	OUT PLUS*
1772648166	10 C	7.5 C	11 C	-126 C	2 C
1772646405	10 C	7.5 C	11 C	-126.5 C	1.5 C
1772644665	10 C	7.5 C	11 C	-126.5 C	1.5 C
1772642890	10 C	7.5 C	11.5 C	-126.5 C	1.5 C
1772641131	10 C	7.5 C	11 C	-127 C	1 C
1772639374	10 C	7.5 C	11 C	-127 C	1 C
1772637616	10 C	7.5 C	11 C	-127.5 C	0.5 C
1772635858	10 C	7.5 C	11 C	-127.5 C	0.5 C
1772632342	10 C	7.5 C	11 C	-127 C	1 C
1772627068	10 C	7.5 C	11 C	-125.5 C	2.5 C
1772625315	10 C	7.5 C	11 C	-126 C	2 C
1772623553	10 C	7.5 C	11 C	-126.5 C	1.5 C
1772621795	10 C	7.5 C	11 C	-126 C	2 C
1772620038	10 C	7.5 C	11 C	-125.5 C	2.5 C
1772618280	10 C	7.5 C	11 C	-126 C	2 C
1772616522	10 C	7.5 C	11 C	-126.5 C	1.5 C
1772614764	10 C	7.5 C	11 C	-127 C	1 C
1772613006	10 C	7.5 C	11 C	-127 C	1 C
1772611248	10 C	7.5 C	11 C	-127 C	1 C
1772609491	10 C	7.5 C	11 C	-127 C	1 C
1772607732	10 C	7.5 C	11 C	-128 C	0 C
1772605975	10 C	7.5 C	11 C	-128 C	0 C
1772604225	10 C	7.5 C	11 C	-128 C	0 C
1772602459	10 C	7.5 C	11 C	-0.5 C	127.5 C
1772600701	10 C	7.5 C	11 C	-0.5 C	127.5 C

*Used Equation Coefficients:

WM: 0, 0.5, 0

YK: 0, 0.5, 0

AK: 0, 0.5, 0

OUT MIINUS: 0, 0.5, -128

OUT PLUS: 0, 0.5, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)