OE1SCS-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE1SCS-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Efftot*
1788566489	12.25 Volt	100 Pcnt	82 Pcnt
1788562889	12.25 Volt	100 Pcnt	82 Pcnt
1788559289	12.25 Volt	100 Pcnt	82 Pcnt
1788555689	12.25 Volt	88 Pcnt	82 Pcnt
1788552090	12.25 Volt	100 Pcnt	82 Pcnt
1788548490	12.25 Volt	88 Pcnt	82 Pcnt
1788544890	12.25 Volt	100 Pcnt	82 Pcnt
1788541290	12.25 Volt	88 Pcnt	82 Pcnt
1788537690	12.25 Volt	100 Pcnt	82 Pcnt
1788534090	12.25 Volt	100 Pcnt	82 Pcnt
1788530490	12.25 Volt	100 Pcnt	82 Pcnt
1788526891	12.25 Volt	100 Pcnt	82 Pcnt
1788523291	12.25 Volt	100 Pcnt	82 Pcnt
1788519691	12.25 Volt	100 Pcnt	82 Pcnt
1788516091	12.25 Volt	100 Pcnt	82 Pcnt
1788512491	12.25 Volt	100 Pcnt	82 Pcnt
1788508892	12.25 Volt	100 Pcnt	82 Pcnt
1788505292	12.25 Volt	100 Pcnt	82 Pcnt
1788501692	12.25 Volt	100 Pcnt	82 Pcnt
1788498092	12.25 Volt	80 Pcnt	82 Pcnt
1788494492	12.25 Volt	88 Pcnt	82 Pcnt
1788490892	12.25 Volt	100 Pcnt	82 Pcnt
1788487292	12.25 Volt	100 Pcnt	82 Pcnt
1788483693	12.25 Volt	85 Pcnt	82 Pcnt
1788476493	12.25 Volt	100 Pcnt	82 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Eff1h: 0, 1, 0

Efftot: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)