VK2JUZ-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2JUZ-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1787582346	13.13 Volt	100 Pkt	96 Pcnt
1787582046	13.05 Volt	100 Pkt	97 Pcnt
1787581746	13.05 Volt	100 Pkt	97 Pcnt
1787581446	13.05 Volt	100 Pkt	97 Pcnt
1787581146	13.05 Volt	100 Pkt	98 Pcnt
1787580846	13.2 Volt	100 Pkt	98 Pcnt
1787580546	13.2 Volt	100 Pkt	98 Pcnt
1787580246	13.05 Volt	100 Pkt	98 Pcnt
1787579946	13.05 Volt	110 Pkt	98 Pcnt
1787579646	13.2 Volt	100 Pkt	97 Pcnt
1787579346	13.05 Volt	100 Pkt	98 Pcnt
1787579046	13.05 Volt	100 Pkt	99 Pcnt
1787578746	13.2 Volt	100 Pkt	99 Pcnt
1787578446	13.2 Volt	100 Pkt	99 Pcnt
1787578146	13.05 Volt	100 Pkt	99 Pcnt
1787577846	13.05 Volt	100 Pkt	99 Pcnt
1787577546	13.13 Volt	100 Pkt	99 Pcnt
1787577246	13.2 Volt	100 Pkt	98 Pcnt
1787576946	13.13 Volt	100 Pkt	98 Pcnt
1787576646	13.13 Volt	100 Pkt	98 Pcnt
1787576346	13.05 Volt	100 Pkt	98 Pcnt
1787576046	13.2 Volt	100 Pkt	99 Pcnt
1787575746	13.13 Volt	100 Pkt	99 Pcnt
1787575446	12.9 Volt	110 Pkt	98 Pcnt
1787575146	12.98 Volt	110 Pkt	96 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)