SR9NSK-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9NSK-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Tempre*
1780532390	78 Pkt	2 Pkt	30 DegC
1780531790	55 Pkt	4 Pkt	30 DegC
1780531186	44 Pkt	2 Pkt	30 DegC
1780530586	66 Pkt	3 Pkt	30 DegC
1780529984	75 Pkt	2 Pkt	30 DegC
1780529384	68 Pkt	3 Pkt	30 DegC
1780528782	87 Pkt	3 Pkt	30 DegC
1780528182	46 Pkt	3 Pkt	30 DegC
1780527581	72 Pkt	6 Pkt	30 DegC
1780526971	77 Pkt	3 Pkt	30.5 DegC
1780526369	73 Pkt	2 Pkt	30.5 DegC
1780525769	59 Pkt	3 Pkt	30.5 DegC
1780525167	80 Pkt	3 Pkt	30.5 DegC
1780524564	78 Pkt	3 Pkt	30.5 DegC
1780523962	71 Pkt	2 Pkt	30.5 DegC
1780523362	74 Pkt	3 Pkt	30.5 DegC
1780522760	59 Pkt	2 Pkt	30.5 DegC
1780522159	74 Pkt	4 Pkt	30.5 DegC
1780521557	96 Pkt	2 Pkt	31 DegC
1780520958	65 Pkt	3 Pkt	31 DegC
1780520356	63 Pkt	2 Pkt	31 DegC
1780519756	79 Pkt	3 Pkt	31 DegC
1780519154	67 Pkt	2 Pkt	31 DegC
1780518554	101 Pkt	8 Pkt	31 DegC
1780517941	103 Pkt	2 Pkt	31.5 DegC

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)