EA5JKT-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EA5JKT-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1772619918	183 Count	458 Count	4.17 VDC
1772618115	182 Count	457 Count	4.21 VDC
1772616311	181 Count	457 Count	4.24 VDC
1772614507	180 Count	456 Count	4.17 VDC
1772612718	179 Count	456 Count	4.17 VDC
1772610900	178 Count	455 Count	4.2 VDC
1772609117	177 Count	455 Count	4.2 VDC
1772607292	176 Count	454 Count	4.26 VDC
1772605488	175 Count	454 Count	4.23 VDC
1772603730	174 Count	453 Count	4.22 VDC
1772601925	173 Count	453 Count	4.24 VDC
1772600122	172 Count	452 Count	4.18 VDC
1772598326	171 Count	452 Count	4.19 VDC
1772596514	170 Count	451 Count	4.22 VDC
1772594710	169 Count	451 Count	4.22 VDC
1772592907	168 Count	450 Count	4.2 VDC
1772591102	167 Count	450 Count	4.22 VDC
1772589299	166 Count	449 Count	4.21 VDC
1772587495	165 Count	449 Count	4.21 VDC
1772585692	164 Count	448 Count	4.2 VDC
1772583887	163 Count	448 Count	4.17 VDC
1772582144	162 Count	447 Count	4.16 VDC
1772580326	161 Count	447 Count	4.17 VDC
1772578522	160 Count	446 Count	4.22 VDC
1772576719	159 Count	446 Count	4.21 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)