OE3CRA-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3CRA-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1762879547	12.32 Volt	300 Pkt	69 Pcnt
1762879546	12.32 Volt	300 Pkt	69 Pcnt
1762879247	12.32 Volt	300 Pkt	70 Pcnt
1762878946	12.32 Volt	290 Pkt	70 Pcnt
1762878646	12.32 Volt	280 Pkt	68 Pcnt
1762878645	12.32 Volt	280 Pkt	68 Pcnt
1762878346	12.32 Volt	280 Pkt	68 Pcnt
1762878345	12.32 Volt	280 Pkt	68 Pcnt
1762877745	12.32 Volt	270 Pkt	67 Pcnt
1762877444	12.32 Volt	280 Pkt	68 Pcnt
1762877144	12.32 Volt	270 Pkt	68 Pcnt
1762876874	12.32 Volt	270 Pkt	68 Pcnt
1762876874	12.32 Volt	270 Pkt	68 Pcnt
1762876545	12.32 Volt	270 Pkt	70 Pcnt
1762876543	12.32 Volt	270 Pkt	70 Pcnt
1762876243	12.32 Volt	270 Pkt	71 Pcnt
1762875943	12.32 Volt	280 Pkt	72 Pcnt
1762875943	12.32 Volt	280 Pkt	72 Pcnt
1762875643	12.32 Volt	300 Pkt	73 Pcnt
1762875643	12.32 Volt	300 Pkt	73 Pcnt
1762875342	12.32 Volt	300 Pkt	73 Pcnt
1762875043	12.32 Volt	300 Pkt	74 Pcnt
1762875042	12.32 Volt	300 Pkt	74 Pcnt
1762874742	12.32 Volt	290 Pkt	71 Pcnt
1762874742	12.32 Volt	290 Pkt	71 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)