SR9NRA Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9NRA. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*	Vbatt*
1788568613	17 Pkt	0 Pkt	0 Pkt	10 V
1788568013	11 Pkt	0 Pkt	0 Pkt	10 V
1788567413	18 Pkt	0 Pkt	0 Pkt	10 V
1788566813	13 Pkt	0 Pkt	0 Pkt	10 V
1788566213	12 Pkt	0 Pkt	0 Pkt	10 V
1788565614	11 Pkt	1 Pkt	1 Pkt	10 V
1788565014	17 Pkt	1 Pkt	0 Pkt	10 V
1788564414	10 Pkt	2 Pkt	2 Pkt	10 V
1788563814	9 Pkt	0 Pkt	0 Pkt	10 V
1788563214	10 Pkt	0 Pkt	0 Pkt	10 V
1788562614	8 Pkt	4 Pkt	0 Pkt	10 V
1788562005	11 Pkt	1 Pkt	1 Pkt	10 V
1788561406	10 Pkt	1 Pkt	1 Pkt	10 V
1788560806	15 Pkt	2 Pkt	2 Pkt	10 V
1788560206	12 Pkt	2 Pkt	1 Pkt	10 V
1788559606	12 Pkt	0 Pkt	0 Pkt	10 V
1788559006	11 Pkt	1 Pkt	1 Pkt	10 V
1788558406	12 Pkt	1 Pkt	1 Pkt	10 V
1788557806	12 Pkt	2 Pkt	2 Pkt	10 V
1788556627	12 Pkt	1 Pkt	1 Pkt	10 V
1788556007	12 Pkt	0 Pkt	0 Pkt	10 V
1788555407	12 Pkt	1 Pkt	0 Pkt	10 V
1788554807	12 Pkt	0 Pkt	0 Pkt	10 V
1788554207	6 Pkt	0 Pkt	0 Pkt	10 V
1788553608	12 Pkt	4 Pkt	0 Pkt	10 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)