DG4MNU-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG4MNU-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vsolar*	Temp*	Eff1h*
1788565490	12.75 Volt	20.29 C	76 Pcnt
1788565190	12.83 Volt	20.29 C	76 Pcnt
1788564890	12.75 Volt	20.29 C	76 Pcnt
1788564590	12.75 Volt	20.29 C	76 Pcnt
1788564290	12.75 Volt	20.29 C	76 Pcnt
1788563990	12.83 Volt	20.29 C	76 Pcnt
1788563690	12.83 Volt	20.29 C	76 Pcnt
1788563390	12.83 Volt	20.29 C	76 Pcnt
1788563090	12.83 Volt	20.29 C	76 Pcnt
1788562790	12.83 Volt	20.29 C	76 Pcnt
1788562490	12.83 Volt	20.29 C	76 Pcnt
1788562190	12.83 Volt	20.29 C	76 Pcnt
1788561890	12.83 Volt	20.29 C	76 Pcnt
1788561590	12.83 Volt	20.29 C	76 Pcnt
1788561290	12.83 Volt	20.29 C	76 Pcnt
1788560990	12.83 Volt	20.29 C	76 Pcnt
1788560690	12.83 Volt	20.29 C	76 Pcnt
1788560390	12.83 Volt	20.29 C	76 Pcnt
1788560090	12.83 Volt	20.29 C	76 Pcnt
1788559790	12.83 Volt	20.29 C	76 Pcnt
1788559490	12.83 Volt	20.29 C	76 Pcnt
1788559190	12.83 Volt	20.29 C	76 Pcnt
1788558890	12.83 Volt	20.29 C	76 Pcnt
1788558590	12.83 Volt	20.29 C	76 Pcnt
1788558290	12.83 Volt	20.29 C	76 Pcnt

*Used Equation Coefficients:

Vsolar: 0, 0.075, 0

Temp: 0, 0.112727, 0

Value3: 0, 0, 0

Eff1h: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)