PU5SUP-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object PU5SUP-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	UpTime*	Pkts*	VCC*
1781475501	150 hours	35 pkts	13.7 volts
1781471740	149 hours	34 pkts	13.7 volts
1781468930	148 hours	36 pkts	13.7 volts
1781467993	148 hours	39 pkts	13.7 volts
1781467050	147 hours	38 pkts	13.7 volts
1781466108	147 hours	39 pkts	13.7 volts
1781465165	147 hours	38 pkts	13.7 volts
1781464223	147 hours	33 pkts	13.7 volts
1781462350	146 hours	35 pkts	13.7 volts
1781460476	146 hours	38 pkts	13.7 volts
1781459536	145 hours	39 pkts	13.7 volts
1781458596	145 hours	38 pkts	13.7 volts
1781456719	145 hours	35 pkts	13.7 volts
1781455782	144 hours	38 pkts	13.7 volts
1781454844	144 hours	30 pkts	13.7 volts
1781452962	144 hours	50 pkts	13.7 volts
1781452052	144 hours	29 pkts	13.7 volts
1781451475	143 hours	57 pkts	13.7 volts
1781450515	143 hours	38 pkts	13.7 volts
1781449573	143 hours	42 pkts	13.7 volts
1781448629	142 hours	55 pkts	13.7 volts
1781445796	142 hours	32 pkts	13.7 volts
1781443922	141 hours	38 pkts	13.7 volts
1781442982	141 hours	36 pkts	13.7 volts
1781441108	140 hours	34 pkts	13.7 volts

*Used Equation Coefficients:

Temp: 0, 1, 0

U.Rel.: 0, 1, 0

UpTime: 0, 1, 0

Pkts: 0, 1, 0

VCC: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)