OH7BD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OH7BD. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Dg1h*	Eff1h*
1776711745	13.58 Volt	1000 Pkt	100 Pcnt
1776708145	13.58 Volt	1000 Pkt	100 Pcnt
1776704545	13.58 Volt	1000 Pkt	100 Pcnt
1776700945	13.58 Volt	0 Pkt	0 Pcnt
1776697346	13.58 Volt	1000 Pkt	100 Pcnt
1776697345	13.58 Volt	1000 Pkt	100 Pcnt
1776693745	13.58 Volt	1000 Pkt	100 Pcnt
1776690145	13.58 Volt	1000 Pkt	100 Pcnt
1776686545	13.58 Volt	1000 Pkt	100 Pcnt
1776682946	13.58 Volt	1000 Pkt	100 Pcnt
1776679346	13.58 Volt	1000 Pkt	100 Pcnt
1776675746	13.58 Volt	0 Pkt	0 Pcnt
1776672146	13.58 Volt	1000 Pkt	100 Pcnt
1776668546	13.65 Volt	0 Pkt	0 Pcnt
1776664946	12.75 Volt	1000 Pkt	100 Pcnt
1776661346	12.75 Volt	1000 Pkt	100 Pcnt
1776657746	12.75 Volt	1000 Pkt	100 Pcnt
1776654146	12.75 Volt	1000 Pkt	100 Pcnt
1776650546	12.75 Volt	0 Pkt	0 Pcnt
1776649347	12.68 Volt	1000 Pkt	100 Pcnt
1776646946	12.75 Volt	1000 Pkt	100 Pcnt
1776643346	12.68 Volt	1000 Pkt	100 Pcnt
1776639747	12.68 Volt	0 Pkt	0 Pcnt
1776636147	12.68 Volt	0 Pkt	0 Pcnt
1776632547	12.75 Volt	1000 Pkt	100 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)