OE8KKK-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE8KKK-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	U BATCd*	TempT*	Rx 1h*	Ef 1h*
1780612893	13.6 V	23.5 C	70 Pkt	35 Pct
1780612594	13.6 V	23.5 C	70 Pkt	33 Pct
1780612593	13.6 V	23.5 C	70 Pkt	33 Pct
1780612292	13.6 V	23.5 C	70 Pkt	34 Pct
1780611992	13.7 V	23.5 C	70 Pkt	35 Pct
1780611692	13.7 V	23.5 C	70 Pkt	37 Pct
1780611391	13.7 V	23.5 C	80 Pkt	40 Pct
1780611091	13.7 V	23.5 C	90 Pkt	40 Pct
1780610794	13.7 V	23.5 C	90 Pkt	40 Pct
1780610791	13.7 V	23.5 C	90 Pkt	40 Pct
1780610491	13.7 V	23.5 C	90 Pkt	41 Pct
1780610190	13.7 V	23.5 C	100 Pkt	43 Pct
1780609890	13.7 V	23.5 C	110 Pkt	43 Pct
1780609590	13.7 V	23.5 C	110 Pkt	44 Pct
1780609289	13.7 V	24 C	120 Pkt	48 Pct
1780608989	13.7 V	24 C	130 Pkt	50 Pct
1780608689	13.7 V	24 C	130 Pkt	50 Pct
1780608389	13.7 V	24 C	120 Pkt	50 Pct
1780608088	13.7 V	24 C	130 Pkt	51 Pct
1780607788	13.7 V	24 C	120 Pkt	52 Pct
1780607488	13.7 V	24 C	130 Pkt	53 Pct
1780607188	13.6 V	24 C	120 Pkt	54 Pct
1780607188	13.6 V	24 C	120 Pkt	54 Pct
1780606887	13.7 V	24 C	120 Pkt	56 Pct
1780606587	13.7 V	24 C	120 Pkt	57 Pct

*Used Equation Coefficients:

I Solar: 0, 0.1687, -21.4241

U BATCd: 0, 0.1, 0

TempT: 0, 0.5, -64

Rx 1h: 0, 10, 0

Ef 1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)