9A2KS-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9A2KS-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1765912251	12.8 Volt	240 Pkt	81 Pcnt
1765911351	12.8 Volt	250 Pkt	80 Pcnt
1765910450	12.8 Volt	250 Pkt	80 Pcnt
1765909549	12.8 Volt	240 Pkt	81 Pcnt
1765908648	12.8 Volt	230 Pkt	79 Pcnt
1765907747	12.8 Volt	230 Pkt	84 Pcnt
1765906846	12.8 Volt	250 Pkt	82 Pcnt
1765905945	12.8 Volt	280 Pkt	85 Pcnt
1765905044	12.8 Volt	310 Pkt	85 Pcnt
1765904144	12.8 Volt	310 Pkt	84 Pcnt
1765903243	12.8 Volt	300 Pkt	88 Pcnt
1765902342	12.8 Volt	290 Pkt	88 Pcnt
1765901441	12.8 Volt	280 Pkt	94 Pcnt
1765900540	12.8 Volt	270 Pkt	95 Pcnt
1765899639	12.8 Volt	270 Pkt	92 Pcnt
1765898738	12.8 Volt	270 Pkt	92 Pcnt
1765896937	12.8 Volt	310 Pkt	90 Pcnt
1765896036	12.8 Volt	310 Pkt	94 Pcnt
1765895135	12.8 Volt	310 Pkt	93 Pcnt
1765892432	12.8 Volt	290 Pkt	89 Pcnt
1765891531	12.8 Volt	300 Pkt	89 Pcnt
1765889730	12.8 Volt	330 Pkt	93 Pcnt
1765888829	12.8 Volt	330 Pkt	88 Pcnt
1765887928	12.8 Volt	340 Pkt	82 Pcnt
1765887027	12.8 Volt	340 Pkt	82 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)