UR7D-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object UR7D-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1784696132	14.14 Volt	90 Pkt	57 Pcnt
1784695531	14.22 Volt	90 Pkt	54 Pcnt
1784694931	14.22 Volt	100 Pkt	59 Pcnt
1784694330	14.14 Volt	120 Pkt	69 Pcnt
1784693731	14.22 Volt	130 Pkt	74 Pcnt
1784693129	14.22 Volt	140 Pkt	77 Pcnt
1784692528	14.22 Volt	140 Pkt	80 Pcnt
1784691928	14.22 Volt	160 Pkt	88 Pcnt
1784691327	14.22 Volt	160 Pkt	89 Pcnt
1784690728	14.14 Volt	160 Pkt	90 Pcnt
1784690126	14.14 Volt	150 Pkt	91 Pcnt
1784689526	14.22 Volt	140 Pkt	89 Pcnt
1784688927	14.22 Volt	150 Pkt	88 Pcnt
1784688325	14.22 Volt	130 Pkt	82 Pcnt
1784687724	14.14 Volt	140 Pkt	81 Pcnt
1784687123	14.22 Volt	130 Pkt	76 Pcnt
1784685922	14.22 Volt	130 Pkt	71 Pcnt
1784685321	14.14 Volt	110 Pkt	65 Pcnt
1784684721	14.22 Volt	100 Pkt	63 Pcnt
1784684120	14.22 Volt	80 Pkt	58 Pcnt
1784683520	14.22 Volt	80 Pkt	53 Pcnt
1784682919	14.22 Volt	60 Pkt	48 Pcnt
1784682319	14.22 Volt	40 Pkt	40 Pcnt
1784681718	14.22 Volt	30 Pkt	37 Pcnt
1784681117	14.14 Volt	30 Pkt	38 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)