BM3FFG-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM3FFG-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1789976912	43.4 C	0 p	0 p	147 p
1789975712	44.2 C	0 p	0 p	147 p
1789974551	44 C	0 p	0 p	147 p
1789973312	43.6 C	0 p	0 p	147 p
1789972113	44.7 C	0 p	0 p	147 p
1789970912	44.3 C	0 p	0 p	147 p
1789969712	43.2 C	0 p	0 p	147 p
1789968512	43.1 C	0 p	0 p	147 p
1789967313	43.1 C	0 p	0 p	148 p
1789966112	42 C	0 p	0 p	148 p
1789964912	42.9 C	0 p	0 p	148 p
1789963712	42 C	0 p	0 p	148 p
1789962512	43.1 C	0 p	0 p	148 p
1789961321	41.9 C	0 p	4 p	148 p
1789960112	42.4 C	0 p	9 p	148 p
1789958912	41.3 C	4 p	9 p	148 p
1789957712	41.2 C	5 p	6 p	144 p
1789956512	40.7 C	0 p	1 p	140 p
1789955312	40.3 C	1 p	2 p	141 p
1789954112	39.5 C	0 p	3 p	140 p
1789952912	39.5 C	1 p	3 p	140 p
1789951712	39.1 C	2 p	2 p	139 p
1789950513	39.2 C	0 p	0 p	137 p
1789949312	39 C	0 p	0 p	137 p
1789948112	37.7 C	0 p	0 p	137 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)