This is the latest recevied telemetry packets stored in our database for station/object DO7BTR-8. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Temp*
Humi*
Baro*
Value4*
Value5*
1754237254
22.1 deg C
54.4 %
1013.5 hPa
0
0
1754234545
22.9 deg C
56.8 %
1014.9 hPa
0
0
1754233648
22.4 deg C
56.5 %
1013.1 hPa
0
0
1754232745
24 deg C
54 %
1013 hPa
0
0
1754231845
23.4 deg C
54 %
1013.2 hPa
0
0
1754230945
23.7 deg C
50.5 %
1012.8 hPa
0
0
1754230044
26.1 deg C
44.8 %
1013 hPa
0
0
1754229147
27.9 deg C
40 %
1013 hPa
0
0
1754228250
30.8 deg C
37.6 %
1013.2 hPa
0
0
1754227350
29.8 deg C
40.3 %
1012.9 hPa
0
0
1754226455
29.5 deg C
39.7 %
1013 hPa
0
0
1754225557
29.6 deg C
40.4 %
1012.9 hPa
0
0
1754224660
28.7 deg C
42.2 %
1016.4 hPa
0
0
1754223750
29.1 deg C
43.3 %
1012.4 hPa
0
0
1754222848
28.3 deg C
45.8 %
1012.4 hPa
0
0
1754221943
27.2 deg C
47.9 %
1012.8 hPa
0
0
1754220140
25.8 deg C
46.9 %
1016 hPa
0
0
1754219243
25.7 deg C
49.2 %
1016.8 hPa
0
0
1754218343
24.2 deg C
51 %
1018.3 hPa
0
0
1754217445
23 deg C
54.3 %
1014.7 hPa
0
0
1754216544
20.9 deg C
57.6 %
1013.2 hPa
0
0
1754215649
21.3 deg C
58.4 %
1013.7 hPa
0
0
*Used Equation Coefficients:
Temp: 0, 0.1, 0
Humi: 0, 0.1, 0
Baro: 0, 0.1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)