IQ5VK-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IQ5VK-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V_Ext*	Value2*	Value3*	Value4*	Value5*
1780890403	13.14 VDC	0	0	0	0
1780888603	13.14 VDC	0	0	0	0
1780886803	13.16 VDC	0	0	0	0
1780885002	13.2 VDC	0	0	0	0
1780883202	13.2 VDC	0	0	0	0
1780881402	13.14 VDC	0	0	0	0
1780879602	13.16 VDC	0	0	0	0
1780877803	13.14 VDC	0	0	0	0
1780876003	13.3 VDC	0	0	0	0
1780874203	13.3 VDC	0	0	0	0
1780872403	13.34 VDC	0	0	0	0
1780870603	13.4 VDC	0	0	0	0
1780868803	13.32 VDC	0	0	0	0
1780867002	13.38 VDC	0	0	0	0
1780865202	13.2 VDC	0	0	0	0
1780863402	13.26 VDC	0	0	0	0
1780861602	13.3 VDC	0	0	0	0
1780859802	13.26 VDC	0	0	0	0
1780858002	13.26 VDC	0	0	0	0
1780856212	13.46 VDC	0	0	0	0
1780856202	13.46 VDC	0	0	0	0
1780854412	13.44 VDC	0	0	0	0
1780854402	13.64 VDC	0	0	0	0
1780852602	13.62 VDC	0	0	0	0
1780850801	13.8 VDC	0	0	0	0

*Used Equation Coefficients:

V_Ext: 0, 0.02, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)