DG0MG-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG0MG-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Ubat*	TxPwr*
1781403105	11.5 degC	4.17 V	12 dBm
1781402803	11.6 degC	4.16 V	14 dBm
1781402501	11.6 degC	4.17 V	13 dBm
1781402199	11.6 degC	4.17 V	14 dBm
1781401596	11.6 degC	4.17 V	14 dBm
1781400992	11.5 degC	4.17 V	14 dBm
1781400388	11.4 degC	4.17 V	14 dBm
1781399785	11.6 degC	4.17 V	14 dBm
1781399483	11.6 degC	4.17 V	10 dBm
1781399181	11.7 degC	4.17 V	14 dBm
1781398876	11.9 degC	4.17 V	11 dBm
1781398574	11.9 degC	4.17 V	14 dBm
1781398297	12 degC	4.17 V	12 dBm
1781397971	12.1 degC	4.16 V	14 dBm
1781397669	12.2 degC	4.16 V	13 dBm
1781397367	12.3 degC	4.17 V	14 dBm
1781396764	12.5 degC	4.17 V	14 dBm
1781396158	12.4 degC	4.17 V	14 dBm
1781395554	12.5 degC	4.17 V	14 dBm
1781395252	12.6 degC	4.17 V	9 dBm
1781394950	12.7 degC	4.17 V	14 dBm
1781394648	12.7 degC	4.17 V	10 dBm
1781394346	12.8 degC	4.17 V	14 dBm
1781394045	12.8 degC	4.16 V	11 dBm
1781393743	12.8 degC	4.17 V	14 dBm

*Used Equation Coefficients:

Temp: 0, 0.1, -273

Ubat: 0, 0.001, 0

TxPwr: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)