CN8UN-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object CN8UN-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1789981764	12.38 Volt	90 Pkt	10 Pkt	40 Pcnt
1789981464	12.38 Volt	110 Pkt	10 Pkt	45 Pcnt
1789981166	12.38 Volt	130 Pkt	10 Pkt	50 Pcnt
1789981164	12.38 Volt	130 Pkt	10 Pkt	50 Pcnt
1789980864	12.38 Volt	120 Pkt	10 Pkt	47 Pcnt
1789980564	12.38 Volt	120 Pkt	10 Pkt	46 Pcnt
1789980264	12.38 Volt	110 Pkt	10 Pkt	42 Pcnt
1789979966	12.38 Volt	100 Pkt	10 Pkt	39 Pcnt
1789979964	12.38 Volt	100 Pkt	10 Pkt	39 Pcnt
1789979664	12.38 Volt	130 Pkt	10 Pkt	45 Pcnt
1789979364	12.38 Volt	140 Pkt	10 Pkt	50 Pcnt
1789979064	12.38 Volt	150 Pkt	10 Pkt	51 Pcnt
1789978764	12.38 Volt	150 Pkt	10 Pkt	54 Pcnt
1789978464	12.38 Volt	130 Pkt	10 Pkt	54 Pcnt
1789978164	12.38 Volt	110 Pkt	0 Pkt	50 Pcnt
1789977864	12.38 Volt	90 Pkt	0 Pkt	47 Pcnt
1789977568	12.38 Volt	70 Pkt	0 Pkt	42 Pcnt
1789977564	12.38 Volt	70 Pkt	0 Pkt	42 Pcnt
1789977264	12.38 Volt	70 Pkt	0 Pkt	47 Pcnt
1789976964	12.38 Volt	100 Pkt	0 Pkt	56 Pcnt
1789976664	12.38 Volt	130 Pkt	10 Pkt	70 Pcnt
1789976364	12.38 Volt	150 Pkt	10 Pkt	77 Pcnt
1789976064	12.38 Volt	140 Pkt	10 Pkt	75 Pcnt
1789975764	12.38 Volt	150 Pkt	10 Pkt	78 Pcnt
1789975464	12.38 Volt	160 Pkt	10 Pkt	80 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)