YC3AFP Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YC3AFP. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	V_Bat*	V_Ext*
1781261181	117 Count	4.25 VDC	0.14 VDC
1781260880	116 Count	4.3 VDC	0.14 VDC
1781260579	93 Count	4.25 VDC	0.14 VDC
1781260328	92 Count	4.21 VDC	0.14 VDC
1781260027	91 Count	4.2 VDC	0.14 VDC
1781259727	90 Count	4.31 VDC	0.14 VDC
1781259426	89 Count	4.32 VDC	0.14 VDC
1781259125	88 Count	4.28 VDC	0.14 VDC
1781258825	87 Count	4.32 VDC	0.14 VDC
1781258524	86 Count	4.29 VDC	0.14 VDC
1781258223	85 Count	4.23 VDC	0.14 VDC
1781257922	84 Count	4.24 VDC	0.14 VDC
1781257622	83 Count	4.24 VDC	0.14 VDC
1781257321	82 Count	4.23 VDC	0.14 VDC
1781257020	81 Count	4.29 VDC	0.14 VDC
1781256720	80 Count	4.28 VDC	0.14 VDC
1781256419	79 Count	4.26 VDC	0.14 VDC
1781256118	78 Count	4.24 VDC	0.14 VDC
1781255817	77 Count	4.26 VDC	0.14 VDC
1781255517	76 Count	4.29 VDC	0.14 VDC
1781255216	75 Count	4.31 VDC	0.14 VDC
1781254915	74 Count	4.29 VDC	0.14 VDC
1781254615	73 Count	4.22 VDC	0.14 VDC
1781254314	72 Count	4.31 VDC	0.14 VDC
1781254013	71 Count	4.31 VDC	0.14 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)