CX5CBA-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object CX5CBA-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	EfTot*
1788678321	12.4 Volt	100 Pcnt	37 Pcnt
1788676521	12.8 Volt	100 Pcnt	37 Pcnt
1788674721	13.19 Volt	100 Pcnt	37 Pcnt
1788672921	12.88 Volt	100 Pcnt	37 Pcnt
1788671121	12.64 Volt	100 Pcnt	37 Pcnt
1788669341	13.04 Volt	100 Pcnt	37 Pcnt
1788667521	12.48 Volt	100 Pcnt	37 Pcnt
1788665721	12.64 Volt	100 Pcnt	37 Pcnt
1788663921	12.32 Volt	100 Pcnt	37 Pcnt
1788662121	12.88 Volt	100 Pcnt	37 Pcnt
1788660321	12.72 Volt	100 Pcnt	37 Pcnt
1788658521	12.64 Volt	100 Pcnt	37 Pcnt
1788656721	12.17 Volt	100 Pcnt	37 Pcnt
1788654921	11.53 Volt	100 Pcnt	37 Pcnt
1788653121	11.61 Volt	100 Pcnt	37 Pcnt
1788651322	11.77 Volt	100 Pcnt	37 Pcnt
1788649522	11.46 Volt	100 Pcnt	37 Pcnt
1788647722	11.61 Volt	100 Pcnt	37 Pcnt
1788645922	12.09 Volt	100 Pcnt	37 Pcnt
1788644122	11.85 Volt	100 Pcnt	37 Pcnt
1788642322	11.53 Volt	100 Pcnt	37 Pcnt
1788640522	11.46 Volt	100 Pcnt	37 Pcnt
1788638722	11.93 Volt	100 Pcnt	37 Pcnt
1788636922	11.77 Volt	100 Pcnt	37 Pcnt
1788635141	11.77 Volt	100 Pcnt	37 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

EfTot: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)