This is the latest recevied telemetry packets stored in our database for station/object OE3PYC-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Celsius*
Rel_Hum*
Atm_Press*
Value4*
Value5*
1784578816
23.5 C
39.91 %
1021.88 hPa
0
0
1784540966
23 C
44.41 %
1024.38 hPa
0
0
1784531126
21.1 C
46.79 %
1026.13 hPa
0
0
1784497071
23.1 C
48.67 %
1021.88 hPa
0
0
1784490572
23.1 C
47.4 %
1020.75 hPa
0
0
1784485900
22.7 C
46.57 %
1019.25 hPa
0
0
1784477862
23.2 C
44.94 %
1020.75 hPa
0
0
1784441427
23.6 C
48.3 %
1016.63 hPa
0
0
1784355502
23.6 C
51.97 %
1018.75 hPa
0
0
1784315785
24.1 C
53.92 %
1019.88 hPa
0
0
1784042398
23.8 C
50.57 %
1019.88 hPa
0
0
1783978883
24 C
50.54 %
1021.25 hPa
0
0
1783971640
24.1 C
49.95 %
1022.5 hPa
0
0
1783954036
24.1 C
50.39 %
1014.25 hPa
0
0
1783945901
24.1 C
49.94 %
1022 hPa
0
0
1783904644
23.6 C
47.26 %
1024 hPa
0
0
1783898103
23.7 C
47.41 %
1020.25 hPa
0
0
1783860500
24.2 C
47.28 %
1023.63 hPa
0
0
1783836773
23.1 C
42.46 %
1022.88 hPa
0
0
*Used Equation Coefficients:
Celsius: 0, 0.1, -50
Rel_Hum: 0, 0.01, 0
Atm_Press: 0, 0.125, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)