UR7D-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object UR7D-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1780617200	12.96 Volt	200 Pkt	120 Pkt	64 Pcnt
1780616900	12.96 Volt	200 Pkt	120 Pkt	63 Pcnt
1780616600	12.96 Volt	190 Pkt	120 Pkt	61 Pcnt
1780616299	12.96 Volt	200 Pkt	120 Pkt	63 Pcnt
1780615999	12.96 Volt	210 Pkt	120 Pkt	65 Pcnt
1780615699	12.96 Volt	210 Pkt	120 Pkt	68 Pcnt
1780615399	12.96 Volt	240 Pkt	140 Pkt	69 Pcnt
1780615098	12.96 Volt	250 Pkt	140 Pkt	70 Pcnt
1780614798	12.96 Volt	250 Pkt	140 Pkt	71 Pcnt
1780614498	12.96 Volt	250 Pkt	140 Pkt	72 Pcnt
1780614197	12.96 Volt	240 Pkt	140 Pkt	72 Pcnt
1780613897	12.96 Volt	240 Pkt	140 Pkt	71 Pcnt
1780613597	12.96 Volt	250 Pkt	140 Pkt	73 Pcnt
1780613297	12.96 Volt	250 Pkt	150 Pkt	75 Pcnt
1780612996	12.96 Volt	260 Pkt	150 Pkt	75 Pcnt
1780612696	12.96 Volt	260 Pkt	140 Pkt	74 Pcnt
1780612396	12.96 Volt	240 Pkt	140 Pkt	74 Pcnt
1780612096	12.96 Volt	230 Pkt	140 Pkt	74 Pcnt
1780611795	12.96 Volt	210 Pkt	130 Pkt	72 Pcnt
1780611495	12.96 Volt	200 Pkt	120 Pkt	72 Pcnt
1780611195	12.96 Volt	190 Pkt	120 Pkt	69 Pcnt
1780610894	12.96 Volt	190 Pkt	120 Pkt	71 Pcnt
1780610594	12.96 Volt	190 Pkt	120 Pkt	73 Pcnt
1780610294	12.96 Volt	180 Pkt	110 Pkt	75 Pcnt
1780609994	12.96 Volt	180 Pkt	110 Pkt	74 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)