YH3NPX-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YH3NPX-6. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1753517726	115 Pkt	31 dBm	12.63 V
1753516783	10 Pkt	31 dBm	12.8 V
1753516247	131 Pkt	31 dBm	13.19 V
1753513835	11 Pkt	31 dBm	12.8 V
1753489186	45 Pkt	-43 dBm	13.39 V
1753487691	43 Pkt	-37 dBm	13.39 V
1753481027	24 Pkt	-33 dBm	13.39 V
1753477844	38 Pkt	-31 dBm	13.39 V
1753475731	10 Pkt	-31 dBm	13.37 V
1753475581	52 Pkt	-30 dBm	13.33 V
1753473703	27 Pkt	-30 dBm	13.39 V
1753470892	4 Pkt	-30 dBm	13.39 V
1753467813	45 Pkt	-30 dBm	13.39 V
1753455392	40 Pkt	-37 dBm	13.39 V
1753449570	10 Pkt	-36 dBm	13.39 V
1753446333	18 Pkt	-33 dBm	13.37 V
1753445984	47 Pkt	-31 dBm	13.39 V
1753437690	18 Pkt	-36 dBm	13.37 V
1753436227	13 Pkt	-33 dBm	13.39 V
1753435160	23 Pkt	-31 dBm	13.37 V
1753429325	7 Pkt	-36 dBm	13.39 V
1753420699	9 Pkt	-37 dBm	13.39 V
1753418127	1 Pkt	-37 dBm	13.37 V
1753418070	18 Pkt	-32 dBm	13.39 V
1753417627	1 Pkt	-36 dBm	13.39 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)