DG0JN-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG0JN-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Ubat*	TxPwr*
1781404407	11.2 degC	3.93 V	7 dBm
1781404105	11.2 degC	3.92 V	2 dBm
1781403803	11.2 degC	3.92 V	7 dBm
1781403498	11.2 degC	3.93 V	3 dBm
1781403196	11.2 degC	3.92 V	7 dBm
1781402894	11.2 degC	3.93 V	4 dBm
1781402593	11.2 degC	3.91 V	7 dBm
1781402290	11.5 degC	3.93 V	5 dBm
1781401686	11.5 degC	3.92 V	6 dBm
1781401384	11.7 degC	3.91 V	7 dBm
1781401080	11.7 degC	3.92 V	0 dBm
1781400778	11.7 degC	3.92 V	7 dBm
1781400476	11.7 degC	3.93 V	1 dBm
1781400174	11.7 degC	3.93 V	7 dBm
1781399872	11.7 degC	3.91 V	2 dBm
1781399570	11.7 degC	3.92 V	7 dBm
1781399268	11.7 degC	3.92 V	3 dBm
1781398966	11.7 degC	3.92 V	7 dBm
1781398662	11.7 degC	3.93 V	4 dBm
1781398359	11.7 degC	3.92 V	7 dBm
1781398057	11.7 degC	3.91 V	5 dBm
1781397755	12 degC	3.92 V	7 dBm
1781397453	12 degC	3.92 V	6 dBm
1781397151	12 degC	3.92 V	7 dBm
1781396849	12 degC	3.92 V	0 dBm

*Used Equation Coefficients:

Temp: 0, 0.1, -273

Ubat: 0, 0.001, 0

TxPwr: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)